TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is really a new pen that was created by two guys in California. They wanted to develop a cool writing instrument that appeared as if a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.

smok pen

The Smok Pen has a built quality that’s just great. I found that even vapinger.com though it is an electronic pen the build quality is simply as good as any of the pens that I have reviewed. It is because of how they made the top cap. You don’t have to be worried about the cap cracking or breaking on you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens is the shape of the coils and the way that they are built. In general the coil on a Smok Pen is bigger than on other pens. I think that they did this deliberately, to make the pen feel more substantial.

If you take a glance at a Smok Pen, you will observe that the body of the pen is round and not smooth like other pens. On the trunk of the pen you will find a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on and off. I really liked this feature because it allows me to use the Smok Pen 22 whenever I feel like smoking.

To utilize the Smok Pen you need to keep carefully the heat button pressed. After the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature it is possible to turn off the heating element. Smok recommends utilizing a 22mm tank. I prefer a more substantial tank, but that’s just me.

Once you put your Smok Pen into the tank you will notice a indicator light come on. The indicator light will stay green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen in to the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids in to the coil heads.

Once you have completed this step, it is best to check to see for anyone who is at the right temperature for the coils to fire. Or even then you should turn the energy off and try again. When you are still not satisfied with your Smok Pen then I suggest you take it in for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I would recommend that you perform the following two steps, then go on and check the Smok Pen to see if it still gets the electronic charging port.

Prior to going any further you should take away the battery from your own pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You need to then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch the coils.

After you have placed the sub-ohm tank in to the pen you need to then place the rest of the components like the wattage, the batteries and the heating element into the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You need to place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you first put the pen into the microwave the electronic reading will show a low voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.

Once the Smok Pen has reached the temperature that it requires to reach you need to then connect the two wires to the positive and negative on the positive post on the Smok unit. You need to then connect the other end of the battery to the negative post on the negative side of the Smok unit. The final step would be to connect the positive cable to the bottom of the Smok’s on / off switch.

After all of the components have been placed in to the pen, you should turn the power on. Following the first test run, you ought to be able to start to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you should take away the battery from the pen and then replace it with a brand new one. For your convenience gleam green light that can be pressed to be able to confirm the battery charging status. When you have done these things and you do not see the green light indicating charging, you should replace the battery.